Steam boiler wear and electric test pump DSY Henan fast boiler's china factory price coal fired steam boiler small series with you about wear and DSY electric test pump wear is one common steam boiler heating surface defects, boiler heating surface is arranged in the boiler the furnace and the flue, in particular a heating surface in the steam boiler flue vertical tail, by the long brush smoke, soot in the flue gas so that the wall heating surface wear thinned, so that heat from the flue gas scouring wall ironed a phenomenon known as wear and tear. Flow rate, the concentration of soot in the flue gas and the hardness of the tube bundle arrangement such factors as the wear rate of the heating surface of the steam boiler and the flue gas is related to the flow rate of flue gas wherein the greatest impact on the wear of the heating surface. Experimentally measured, proportional to the cube of the wear rate of the heating surface tubes and the flue gas velocity, it is necessary to effectively control the flow rate of flue gas. Leakage of the furnace wall, a partial wall flue ash, convection heating surface partially severe slagging will cause a partial flue gas velocity is too large, so that the heating surface tubes local wear increased, further, when the soot blowers work failure, high pressure steam steam heating surface tube will blow erosion, so that the wall thinning. Heating surface tubes often wear area is: cool ash, burner, bullnose, and close to Manhole sootblowing waterwall tube aperture; a lower portion of the flue gas before the steering tube heating surface vertical chamber; vertical tail horizontal heating surface portion of the second row of three tubes of the flue, the lower portion of the second three tubes, tube support edge portion of the clip, close to the furnace wall side of the rows of tubes and the individual tubes and the like projecting tube rows. Heating surface wear reduction methods are: to reduce boiler load, reducing flue gas velocity; burning coal quality, reducing the content of fly ash in the boiler flue gas steam; change bundle arrangement, a staggered arrangement to the line arrangement; Clear slagging and blocking flue ash, flue gas flow area increases; leakage reduction furnace wall; the installation of a shoe or the spoiler like. Abrasion test on the electric pump plunger hole set DSY electric test checking pump plunger sleeve (1) Check the DSY type. If the pump DSY electric test has passed the test on sealing ST-990 or the tester 3,375,375, the plunger sleeve is available. If the leakage is large, it is necessary to replace the plunger and plunger sleeve. (2) using the burr, coke, and high-expansion magnifying glass to check the amount of deformation of the bore. When the metering orifice is damaged, DSY i.e. electric test pump is not working properly. Do not attempt to clean with a wire, plug, etc., should be cleaned with a solvent. (3) Check the fuel oil channel as well as choking loose plunger sleeve for cracks. (4) Check DSY electric test pump plunger sleeve surface endless belt black area and Degree how damage flatness. Some electric test pump head end of the barrel nozzle sump has been canceled. Henan is committed to fast boiler steam boiler manufacturing, product quality, reasonable prices and widespread industry praise, if you have any needs, please contact us!

Today, the principle of china factory price coal fired steam boiler and the construction of steam boiler too many forms, take an ordinary fast-packed 4-ton steam boiler. Water is heated into steam in the drum and heat is emitted by fire in the furnace, which is the principle of the steam boiler. Say the boiler first the pot. The boiler is a drum boiler with water cooling. Two return pyrotechnic tubes are arranged in the left and right parts of the drum, and the front cigarette box in the front part of the drum is turned back. Between the drum and the bottom box, there is a drop tube and a water-cooled tube, forming the frame of the combustion chamber. There is a steam separator on the top of the drum to reduce the water produced by steam. The heating surface of the boiler body is the lower part of the drum, the water-cooled pipe and the Pyrotechnic pipe The combustion part is composed of a chain grate and a drive device, and a combustion chamber composed of a boiler rack on the grate frame. Surrounded by refractories. Coal from coal hopper, there are coal gate to control the thickness of coal seam while sealing the front of the air. The lower part of the combustion chamber is the place where the blast enters, and this kind of boiler has great resistance and needs forced blast. Cinder, discharged from the back of the grate through hawk iron and sent out of the furnace by the slag extractor. From the back of the boiler, the flue gas goes forward from the first return pipe of the boiler, the second return pipe returns to the rear part of the boiler, and then goes into the dust collector to separate the ash, and then through the draught fan, it is discharged from the chimney. The induced draft fan not only discharges smoke, but also It is necessary for the negative pressure operation of the boiler. Essential water level gauges, pressure gauges, safety valves, thermometers, electric pumps that can replenish water under pressure, and steam pumps that can also be used in the event of power outages. Boiler water must be softened and water treatment equipment. Steam boilers are force vessels and safety devices are necessary. All steam boilers can work better only in accordance with the correct operating methods.

Fuel oil combustion process differs from the process industry Industrial Combustion fuel oil-fired boilers for industrial oil fired boilers and industrial boilers, having a certain temperature and pressure injected into the furnace through the nozzle is atomized into fine droplets, and then absorbs heat in the furnace, vertical oil-fired boiler, surface gradually vaporized into oil, mixed with intake air in the furnace, form a combustible mixture. The combustible mixture continues endotherm temperature reached ignition ignition combustion. Fuel amount, air amount and the amount of the composite has a one to one relationship of steam, it is necessary according to the load amount of steam required to control the amount of fuel and air supply, but also by the wind furnace pressure control apparatus. Different oil-fired boiler with a different point of industrial coal-fired boilers point of industrial boiler fuel industry and industrial coal-fired boilers. PM2.5 pollution damage to the environment led some coal-fired boilers industrial boilers is facing new boiler renovation or change of situation, which makes oil-fired boiler to become the darling of the market. Oil-fired boiler with a coal-fired boiler in comparison with structurally quite different purposes, as follows: (1) injecting fuel into the boiler furnace through the burner, combustion chamber without using fire grate facilities; (2) Since the oil, gas did not produce combustion ash, it is no oil or gas boiler slag and slag outlet device; (3) injecting a gas or oil furnace materialized, if mixed with air or flame within a certain range, is easy to form an explosive gas, Thus fuel (gas) required automated combustion boiler system, comprising a flame monitoring, flame protection, explosion-proof safety; (4) Since the oil, gas calorific value is much larger than the calorific value of coal, so the thermal strength than fired furnace high multi-furnace, so relatively small and the capacity of the boiler with coal-fired boilers, compact, small footprint; combustion process (5) fuel (gas) is suspended in a boiler furnace, the furnace is provided so its before and after the arch, the furnace structure is very simple. Meter manufacturing, Supervision, Inspection and the main characteristics of biomass fuel boilers [] protection devices and control systems introduced a biomass fired boiler biomass fuel boilers are in strict accordance with "Steam Boiler Safety Supervision", JB / T10094-2002 "general industrial boilers technical conditions ", JB / T1619-2002" shell boiler body manufacturing technology, "execution, ensure long-term security and stability of the boilers. Body is a shell type three return all wet back downstream pyrotechnic pipe structure, large combustion flame in the combustion chamber a slight positive pressure, stretched stretch, combustion heat load is low, less NOx emissions of harmful substances. Waveform furnace and threaded pipe structure that improves the strength, but also to meet the needs of each portion of the thermal expansion. Master butt welds are connected, and by X-ray and ultrasonic nondestructive testing, to ensure the welding quality to meet national requirements. Boiler water volume and large air space, adaptable load capacity. Design reasonable pot, with water vapor to ensure that less than 4%, to meet user requirements for higher quality steam. Using the new insulation materials, light weight, low heat loss, good insulation properties. Water level alarm stainless steel rods as electrodes, an insulating material as polytetrafluoroethylene. Inserted from above, linked to pollution easy, reliable, and long service life. Before and after the smoke box is hinged, can easily open, repair and maintenance quick and easy maintenance. Adjusting the oxygen content (optional): The system can successfully monitor the oxygen content in the flue gas, and transfer the data to the real-time control systems, intelligent analysis by a computer, the automatic adjustment device stoichiometric combustion, it is in real-time good working shape, combustion efficiency is greatly improved, which can significantly reduce fuel consumption. Biomass fuel boiler operation timing of the protection device, the operation of the control system by the timer, the system automatically enters the work or off duty. The control system may be provided multiple sets of the timing period within 24 hours. Any period of time in a group of a plurality of sets of timing of the current time period, the system enters the working state. Work within the timing period, the status screen is displayed automatically. In the period of time in commuting to work outside the state. Each group comprises a turn-on time period (hour, minutes) and a closing time (hours, minutes) may be set or modified when the three control period, divided by the setting operation and the current time. The user can set different time different temperature ranges.

Inside the Fangkuai boiler plant, there is a special corrugated furnace bladder production line, which can be processed according to the computer setting mode. At the same time, this is also a unique processing technology of Fangkuai Boiler. The cost of natural gas fuel alone exceeds 5 million yuan per year. The corrugated furnace liner fired by this production line can not only increase the heating surface of the boiler, but also alleviate the damage caused by the thermal expansion and contraction to the combustion chamber, and greatly extend the service life of the boiler.