The pollution-free environmental benefit of dzl coal fire tube hot water boiler is obvious: renewable biomass energy is used as fuel to realize the sustainable utilization of energy. Adopting high temperature subsection combustion technology and low emission of NOX,SO2, dust in flue gas, it is the best substitute for fuel (gas) burner, electric heating and so on. Internal inspection and preparation of hot water boiler, inspection of furnace and flue, inspection of boiler accessories, inspection of automatic control system, inspection of ancillary equipment, inspection of combustion equipment, inspection of auxiliary heating surface, The hot water boiler must do some inspection before running, these checks are not to be underestimated, possibly because of our neglect Cause very serious consequences. Therefore, we must guard against micro, hot water boiler operation before careful inspection of the following items. Including boiler internal inspection and use preparation. The furnace and flue inspection, furnace and flue dust and debris should be cleared. Air duct and flue adjustment doors, gates shall be complete and tight, flexible switches, accurate opening and closing instructions. Boiler accessories inspection, check the safety accessories are intact; cock rotation flexible, easy to use; all kinds of instruments and control devices should be complete, good, clean. After the check has passed, the pressure gauge plug should be kept in working condition. Automatic control system inspection. Inspection of ancillary equipment. The combustion equipment is checked to check if the combustion device is in good condition; the mechanical transmission system, the coal conveying system and the ballast system are tested normally; the pressure degree of the safety spring of the speed regulating box should be appropriate and the lubrication is good; the gauge of the coal brake is correct. Eagle iron neat, intact, ballast board integrity, flexible movement. Check auxiliary heating surface to check whether auxiliary equipment (induced fan, blower, pump, etc.) coupling is firmly connected; triangular belt is properly tightened; lubricating oil should be good and adequate; cooling water is unobstructed. After inspection, install safety shield, test operation separately, and pay attention to the current of idling. Internal inspection and preparation of hot water boiler The inspection of furnace and flue, the inspection of boiler accessories, the inspection of automatic control system, the inspection of ancillary equipment, the inspection of combustion equipment, the inspection of auxiliary heating surface, and the inspection of hot water boilers must be made before running. These examinations are not negligible and may have very serious consequences as a result of our neglect.

Today, the principle of steam boiler and the construction of steam boiler too many forms, take an ordinary fast-packed 4-ton steam boiler. Water is heated into steam in the drum and heat is emitted by fire in the furnace, which is the principle of the steam boiler. Say the boiler first the pot. The boiler is a drum boiler with water cooling. Two return pyrotechnic tubes are arranged in the left and right parts of the drum, and the front cigarette box in the front part of the drum is turned back. Between the drum and the bottom box, there is a drop tube and a water-cooled tube, forming the frame of the combustion chamber. There is a steam separator on the top of the drum to reduce the water produced by steam. The heating surface of the boiler body is the lower part of the drum, the water-cooled pipe and the Pyrotechnic pipe The combustion part is composed of a chain grate and a drive device, and a combustion chamber composed of a boiler rack on the grate frame. Surrounded by refractories. Coal from coal hopper, there are coal gate to control the thickness of coal seam while sealing the front of the air. The lower part of the combustion chamber is the place where the blast enters, and this kind of boiler has great resistance and needs forced blast. Cinder, discharged from the back of the grate through hawk iron and sent out of the furnace by the slag extractor. From the back of the boiler, the flue gas goes forward from the first return pipe of the boiler, the second return pipe returns to the rear part of the boiler, and then goes into the dust collector to separate the ash, and then through the draught fan, it is discharged from the chimney. The induced draft fan not only discharges smoke, but also It is necessary for the negative pressure operation of the boiler. Essential water level gauges, pressure gauges, safety valves, thermometers, electric pumps that can replenish water under pressure, and steam pumps that can also be used in the event of power outages. Boiler water must be softened and water treatment equipment. Steam boilers are force vessels and safety devices are necessary. All steam boilers can work better only in accordance with the correct operating methods.

Our company processes in multiple new energy automobile production will need to heat, the boiler equipment we choose is really a headache, fast Boiler solve our urgent needs. The purchase of electric water boiler system is simple, easy to operate, easy to maintain, high thermal efficiency, saving a lot of operating costs for our company. --customer feedback

How much gas steam boiler power and water consumption about? One ton of steam coal boiler is about 85 kilograms, a ton of steam consumption of natural gas is about 80 square. I do not know the local fuel prices. Meanwhile, steam boiler tons of gas consumption to about 7 degrees, and tons of gas boiler steam power was insufficient. This is the cost of consumption, you can according to the local point, calculate the cost of coal. Other aspects of superior gas or gas, such as environmental protection, operating environment, repair and maintenance.