Around the city to promote the coal to gas project, the major institutions of the heating system put forward higher requirements. Central Conservatory of Music is available to students and teachers clean, safe, comfortable, energy-efficient heating environment, protect the health of teachers and students, to transform the traditional large boiler treatment. Praise fast boiler Willie sharp series obtained in the transformation of low nitrogen boiler major institutions in Beijing, the Central Conservatory of Music in late 2017 with the signing of fast boiler boiler purchase contract, ordered six Willy sharp series V6-99, to for the entire school's heating facilities.

Gas-fired steam large boiler safety valve from installation to use, it must remain vigilant safety valve is one of the most important components of the gas steam boilers, boiler probability of the risk occurring due to various incidents can effectively suppressed. This article focuses on the safety valve from installation to use several important considerations, we do not ignore the use of gas when it steam boiler. A Notes 1 safety valve, the safety valve should be mounted vertically in a high position in the pot business, set box. 2, between the safety valve and the drum or header, not equipped with access to the steam outlet pipe and the valve. 3, the lever-type safety valve should prevent movement of the self-apparatus and the weight limit leverage deviant guide tube, a spring safety valve should lift and handle means for preventing movement of the adjustment screw is screwed lightly. 4, the rated steam pressure less than or equal to 3.82MPa gas steam boiler safety valve throat diameter of not less than 25mm; power greater than the rated steam pressure 3.82MPa boiler safety valve throat diameter not less than 20mm. 5, the safety valve and coal-fired steam boiler tubes, the cross-sectional area not less than the cross-sectional area of ​​the valve inlet. If several valves installed together with a short tube directly connected to the drum, the cross-sectional area of ​​the passage should not step short tube to 1.25 times the area of ​​all the exhaust valve. 6, the safety valve should normally be installed exhaust pipe, exhaust pipe should be through a safe place, and there is sufficient cross-sectional area to ensure the smooth flow of exhaust. 7, the safety valve exhaust pipe at the bottom should have received a place of safety posturing of drainage pipe, the exhaust pipe and drainage pipe not allow the installation of the valve. 8, rated evaporation to 0.5t h coal-fired steam boiler /, at least two safety valves installed; Rated evaporation 0.5t h less than or equal to electric boiler /, mounted on at least a safety valve. 9, separable economizer outlet, the steam superheater outlet valve must be installed.

How to improve the thermal oil large boiler efficiency oil boiler thermal efficiency is a lot of users are taken into account, we believe that this issue is the direction of each used in the production of various types of oil boiler manufacturers have been in the study. Many users at the time of the oil furnace to operate, often in the actual production process, we found some new problems, but all the problems, the headache is higher oil boiler flue gas temperature, low thermal efficiency the phenomenon that a serious impact on our work, then how should we do to improve the thermal efficiency of it? need to understand this is to meet the low-temperature characteristics of the thermal oil comes as synthetic heat transfer oil. However, the vast majority of synthetic HTF complex biphenyls, benzene derivatives of both components, or a vapor of volatiles has strong carcinogenicity, it is strongly recommended to select customers conducting oil mineral oil products. Second, conducting oil products to meet the low temperature performance process, but also have a relatively high flash point required. In general, oil engineers suggest, low flash point not lower than the HTF opening 200 ℃. After a professional manufacturer of continuous research and improvement of its equipment, in order to improve its thermal efficiency was found to be increased oil boiler heating surface of the tail, say, air preheater and economizer. But when organic heat carrier furnace return temperature is high, you can not set the economizer, air preheater can only be set to alleviate the situation. So if the oil boiler and not other low-temperature heating system heat exchanger, then the only way to improve energy efficiency is adding air preheater. After adding air preheater can be a corresponding increase in the flow rate of heat-conducting oil, oil boiler in order to ensure safe, reliable and stable work, the thermal efficiency of the boiler plant with thermal oil will be a corresponding increase.

The reason the gas large boiler burner noise increases are what it? When making use of gas-fired boiler, we found this small fire normal, but this time turn the fire, extinguished or flashing instability. First speaking, that is because of this fire damper of the air volume setting is too large; i.e. after an oil fire because the micro-switch valve (air outside that group) inappropriate setting (set lower than the fire damper of the air volume is also Big)