Harbin Thermal Power Co., the main city of Harbin is the largest cogeneration business, the company bear the city's heating area of ​​24 million square meters, to provide heat supply for more than 400 agencies, enterprises and 140,000 residents. Currently, the company is actively respond to the latest environmental standards introduced in China, the group mobilized up and down, stepping up technological innovation, upgrading environmental protection facilities, the project is expected to complete upgrading coal-fired boiler at the end of this year.

Harbin Thermal Power Co., the existing five boilers for heating and power generation: where to cogeneration units No. 7,8,9, and the other two hot water boilers. No. 9350 MW units which since 2017 was completed and put into operation, has achieved ultra-low emissions standards during construction. 7, No. 8 is 300 MW units were built in 2005 and 2006, these two units of environmental transformation began in 2013. Harbin Thermal Power Co., according to the latest environmental requirements, environmental upgrading facilities. First, soot emissions transformation, the introduction of advanced electric bag filter, followed by addition of sulfur, in addition to the transformation of nitrate, new burners in addition to the low nitrogen oxides of nitrogen, a wet desulfurization technologies in addition to sulfur dioxide. After four consecutive years of continuous transformation, 7,8 units in 2017, all the transformation is completed, achieve ultra-low emissions standards. For the two 116 MW hot water boiler was built in 2013, it has long been included in the transformation plan. Earlier this year preparatory work has been completed and environmental transformation has entered the bidding process in mid-October to start construction, completed renovation project at the end of December.

Multi-fuel condensing water tube steam boiler supplier protection water protection Fuel steam boiler: boiler water level gauge plate supporting one to two, should always be compared with each other, findings indicate inconsistency shall be corrected immediately. Class water level should be flushed, to determine their true level. While the water level comes electrode rod can accurately capture level signal to an alarm or a pump control. A steam pressure protection, the pressure controller: selection of high sensitivity of the pressure controller, the pressure is high, or low levels of signal to the electrical switches, automatic control chain protection or other control lines. Using pressure controllers and electrical contacts, the vapor pressure can overpressure alarm; single adjustable pressure controller or dual fire burning fire the actual operating pressure. 2, the safety valve: safety valve is the last line of defense to protect the boiler, the boiler pressure exceeds the limit, according to the set pressure relief valve design with the school, the exhaust steam pressure relief, to ensure the normal operation of the boiler. Flame protection: imported burner having a flame protection device, combustion function is to detect, when the ignition failure or extinguish combustion middle, immediately off the burner into the oil (gas) solenoid valve, the blower continues to operate at this time, the furnace was purged of residual internal combustible gas, after 20 to 30 seconds purge, and various auxiliary blowers automatically cut off power, the boiler operation stops. Self-locking power failure protection: Under the emergency power supply is interrupted, the boiler shutdown immediately self-locking, if the current power is restored, the boiler will not start at any time, you must reset release self-locking, to re-start the ignition.

Hot water boiler fuel oil hot water boilers brief automatic control system has a high-tech, with a number of security devices, water protection, overpressure protection, flame protection, abnormal pressure protection, over-temperature flue protection; structure using tech, having a body holding a small, compact and easy to install, easy to operate, automatically adjust the pressure of the fuel to the atomizing, a slight positive pressure of the combustion so that fuel combustion and then more fully, and to reduce the loss of the fuel gas discharge, modern industrial steam is the most convenient and most energy-efficient, environmentally friendly standard products. The need for comprehensive maintenance of the gas hot water boiler gas hot water boiler for normal use, to do regular inspection and maintenance, however, has been used for a three-year-old boiler, we must conduct a more comprehensive repair work. 1, carrying out comprehensive maintenance check, the first thing to be clear inside the boiler ditch and sludge, after using water to rinse these ditches and sludge. 2, the boiler for burning site, there will be a large amount of soot and fouling, but also in such substances when overhaul, the cleanup process. 3, because the gas hot water boiler is used in metal processing and production, but also a lot of contact with water or steam, it is inevitable there will be erosion situation, when the boiler overhaul, to the corrosion phenomena boiler maintenance treatment Finally, we need to do to level the boiler fire boiler use paint protection to prevent future corrosion conditions.

Why boiler furnace exhaust gas temperature increases heat losses the heat loss is largest in a boiler, furnace 6% is generally fed to the heat, the exhaust gas temperature increasing every 12 ~ 15 ℃, heat losses to an increase of 0.5%. Therefore, the exhaust gas temperature is one of the most important indicators boiler operation. Here are a few reasons may cause the furnace exhaust gas temperature rise: (1) heating surface slagging, fouling. Whether waterwall slagging furnace fouling, or superheater, convection bank, and economizer preheater fouling are due to increased resistance measured smoke, heat deterioration of the cooling effect deteriorates the flue gas, resulting in increased exhaust gas temperature. (2) the excess air ratio is too large. Under normal circumstances, the furnace outlet increases as the excess air ratio of the exhaust gas temperature rises. After the excess air ratio increases, while the amount of smoke increases, the speed increase of smoke, heat strengthening of exiled, but less than the degree of increase in heat transfer gas volume increases more. It will be appreciated as the tobacco rate increased, the time to heat to the flue gas working fluid left the heating surface. (3) leakage factor is too large. Tail shaft furnace and boiler flue negative pressure leakage is inevitable, and provides a heating surface allowed leakage coefficient. When the coefficient of air leakage increases, the influence of the exhaust gas temperature and overfire air coefficient increases similarly. And the closer the leakage furnace, exhaust gas temperature raising effect on the greater. (4) water temperature. When the turbine load is low or high pressure splitting when the heater temperature of the boiler feedwater will decrease. Generally, when the water temperature rises, if the amount of fuel is maintained constant, the temperature difference decreases economizer, economizer heat absorption decreases the exhaust gas temperature rises. (5) the fuel moisture. The fuel in the flue gas to increase the amount of water increases, and therefore the exhaust gas temperature rises. (6) boiler load. Although the boiler load increases, the amount of smoke, the amount of steam to the water, the air amount increases in proportion, but since the furnace exit gas temperature is increased, so that the exhaust gas temperature rises. After the load is increased to increase the furnace outlet temperature, followed by convection heating surface temperature difference increases, an increase in heat absorption, the more so the convection heating surface, the smaller the impact load change of a boiler exhaust gas temperature. (7) The fuel species. When burning low calorific value gas, since the furnace temperature is lowered to reduce the radiation heat transfer in the furnace, the low calorific value gas in a non-combustible components, mainly N2, CO2, H2O more, the amount of flue gas increases, the exhaust gas temperature rise high. Pulverized after burning oil, although oil-fired furnace outlet when the excess air ratio than the coal is low, but the little ash fuel oil, and no larger soot particles, larger ash particles in the flue gas absent the cleaning action of surface heating, convection heating surface more polluting. So bad combustion, often black smoke boiler flue gas temperature. When the tail has means ash ball, since the tail cleaner, the exhaust gas temperature is slightly lower than the burning coal. (8) milling system operation. Bunker has a reservoir of closed milling system is concerned, when the pulverizing system is running, because a portion of the water in the fuel into the furnace, the furnace temperature is reduced and the amount of smoke increases, the leakage into the pulverizing system is running as the primary cold air air into the furnace, to reduce the amount of air flowing through the air preheater to the exhaust gas temperature rises. Conversely, when the exhaust gas temperature is reduced pulverizing system outage.