For example, the low-nitrogen condensing oil and gas thermal boiler for clothing industry adopts advanced condensing technology to make secondary use of the high-temperature flue gas generated by the boiler operation, fully absorb the waste heat of the flue gas, and the boiler efficiency can reach 98%, which can save a large input cost for the paper mill. And the boiler adopts the world's advanced technology--FGR technology, using flue gas recirculation, the flue gas generated by the boiler operation is re-entered into the furnace through the connecting pipe, and the function of low nitrogen oxides is achieved by lowering the combustion temperature, which is a green energy-saving energy-saving pioneer. .

Steam thermal boiler for clothing industry is one of the indispensable devices in the pharmaceutical industry, decoction of Chinese medicine, medicine drying, sterilization, cooking gum, drying, tabletting and capsule production processes, a large amount of steam will be used. West Libang Pharmaceutical Co., Ltd. is a pharmaceutical research and development, production and sales of high-tech enterprises, the existing anesthesia, cardiovascular, child immunization, pharmaceutical raw materials, pharmaceutical excipients, nutrition series of six automated production lines. With the increasing strength of China's environmental protection, some high-pollution devices are making the transition to clean environmental protection. Libang Pharmaceutical respond positively to national coal to gas policy, decided to change the existing coal-fired boilers to clean better gas steam boiler. Fast boiler with strong comprehensive strength in the field of clean energy, Libang Pharmaceutical after conducting comprehensive consideration, determined to cooperate with the fast boiler. The two sides further understanding, party fast technical engineers according to production needs state power, and soon its development of specific solutions for its recommendation of a 6 tons of steam condensing gas steam boiler (WNS6-1.25-Y.Q).

6MW YQW series gas-fired thermal oil heater project for food industryThe rapid development of the food industry is inseparable from the strong support of the thermal boiler for clothing industry system, which is one of the important production line equipment for the plant extraction process. Founded in 1995, Damin Food (Zhangzhou) Co., Ltd. is an international enterprise group specializing in deep processing of natural plants which integrates R&D, production and sales. Its products are exported to the United States, Japan, Europe and other countries and regions. It is an international supplier of many large-scale food and beverage, restaurant chain and health care products pharmaceutical companies.Damin Foods is committed to producing healthy and natural products and creating a healthy lifestyle that returns to nature. Therefore, Damin Foods attaches great importance to its own green development, and adheres to the environmental protection concept in the selection of boiler equipment. It plans to introduce environmentally friendly boilers that use clean energy natural gas as fuel. After understanding their actual needs, ZOZEN tailored the technical solution for Damin Foods: newly construct four sets of 5 million kcal YQW series thermal oil heaters. This series of gas-fired thermal oil heaters has the characteristics of high temperature and low pressure. In the process of plant extraction, high temperature steam is used to complete the sterilization process of plant concentrate, which fully meets the temperature requirements of Dagu food production line. The tail of the heater is also equipped with waste heat recovery devices. By recycling the waste heat of high-temperature flue gas, the heat energy loss is greatly reduced, and the overall thermal efficiency of the heater is increased to over 95%.

Burner and flue installation and electrical installation and the fuel supply system of the burner 1, burner 1) before installation read "burner manual", according to the installation requirements. 2) Burner mounting flange, the middle requirements, to ensure the burner to the thermal boiler for clothing industry flue gas does not leak at the interface. 2, the installation of fuel supply system (see schematic) Note: To prevent a fire caused by generation of static electricity in the fuel tank, the tank should have a good grounding. 1) supply system tank top tank top-feed system suction recommended distance between the back plane and the tubing inside diameter of the oil pump axis, the total length of the suction pipe Hm, m, no greater than DL6-34DL40-75DL100-250Di = 10mmDi = 14mmDi = 16mm0.51.03030401.535452.03535452.540503.0404050 Notes: (1) when there is an elbow or valve on the suction pipe, each of the length of the suction pipe to be minus 0.25m. (2) Di recommended internal diameter suction pipe and return pipe. 2) the distance between the bottom of the tank bottom of the tank supply system supply system pipe inner diameter recommended oil pump axis and a plane, the total length of the suction pipe Hm, m, no greater than DL6-34DL40-75DL100-250Di = 10mmDi = 14mmDi = 16mm1.03030401.535452.03535452.540503.04040504.045 Notes: (1) when there is an elbow or valve on the suction pipe, each of the length of the suction pipe to be minus 0.25m. (2) Di recommended internal diameter suction pipe and return pipe. 3, gas pipe installation requirements Burner gas line itself has been connected, the intake port, the intake pipe bends should be minimized and good sealing performance requirements, to prevent leakage. (Iv) a chimney installation, to prevent leakage, the leakage of smoke, to prevent smoke inhalation chamber. 2, a vertical mounting, a right angle bend bends should be avoided. 3, the top of the chimney must be water-resistant measures. (E) mounting a power switch with electrical connection box 1, the power switch should be considered easy to operate, away from heat, fixation, meet the design requirements. 2, the use of 220V (380V), 50HZ power source, and a ground line. 3, voltage instability in the region use, should be safe regulators. Or affect the normal operation of the combustion engine. 4, the power cord to the electrical box must be connected in strict accordance with the requirements, otherwise, there will be dangerous!